The racer asked
set up long pile astroturf indoors
Miles, So Dialed's RC setup AI
For long pile astroturf indoors, start from the high grip astroturf setup for the RC10 B84/D. It lowers the ride height and raises the axles, which keeps the car planted on the high-grip surface. These values are changed from the kit setup, which is set for dirt.
- Ride height: 12 mm front and rear, down from 17 mm.
- Front axle height: +3 mm, up from +2 mm.
- Rear axle hub inserts: +3 mm (0 down / 3 up), up from +1 mm.
- Rear springs: 2.2lb Blue (#91950), softer than the kit 2.3lb Yellow. Softer rear adds rear grip.
- Front shock oil: 42.5 wt, up from 35 wt. Thicker front oil reduces front grip.
- Rear shock oil: 35 wt, up from 30 wt.
- Anti-roll bars: front 1.6 mm (up from 1.3 mm), rear 1.7 mm (up from 1.4 mm).
- Rear wheelbase arm shims: 4 mm, up from 2 mm.
- Front toe: +1 degrees, up from 0.
- Diff fluid: front 20,000 cst, rear 30,000 cst, center 500,000 cst.
- Tires: Jconcepts Pink compound front and rear.
The stiffer bars and thicker front oil both take grip from the front, so this setup can push on corner entry. If it does, back off the front oil first. Do that one change at a time, and if the rear steps out on exit, soften the rear bar before touching the rear springs again.
I'm assuming the kit setup as your starting point. If you type your current settings, I can point to the change that matters most. The RC Setup App can also keep your setups and give advice based on them.
Follow-up
I only have the standard roll bars
Miles
Run the kit anti-roll bars: 1.3 mm front and 1.4 mm rear. The astroturf values I gave earlier (1.6 mm front, 1.7 mm rear) are a step stiffer at both ends, so they aren't needed.
- Front anti-roll bar: 1.3 mm (kit), not 1.6 mm.
- Rear anti-roll bar: 1.4 mm (kit), not 1.7 mm.
Softer bars let the car roll more, which gives more mechanical grip at each end and makes the car less likely to push on entry. Since they're the only change, the rest of the setup stays as listed.
I also need to correct my last answer. I said both bars took grip from the front. A stiffer rear bar actually takes grip from the rear, so the stiffer bars were reducing grip at both ends, not just the front.
If the car feels too loose on exit with the kit bars, the next change is the rear springs, not the bars.
Follow-up
can you pdf this so i can priint it
Miles
I can't make PDFs or printable files, but you can print this page directly from your browser (Ctrl+P or Cmd+P). For a printable copy of the setup, type the settings into a note or print the list above.
Answered by Miles, our RC setup AI. Check anything that affects safety or fitment against your manual.
More RC10 B84/D questions
How do I get more grip on my RC10 B84/D at Tacoma RC Raceway?
Start with the tires: at a smooth, clean clay track, try a clay slick or ghost slick; if there’s dust on top, use a pin tire suited to dusty hardpack instead. The right tread and...
Are there more setup examples for the Team Associated RC10 B84/D?
Yes. There are other-driver setup references for the RC10 B84D across carpet, astroturf, hard-packed, and loose/loamy tracks. They’re setting examples rather than complete...
What spur gear size for Team Associated RC10 B84/D stock setup?
Use a 78-tooth spur gear for the RC10 B84/D’s basic stock setup. That is the kit setup default; the car also supports 72-, 75-, and 81-tooth spurs for gearing changes.
Which rear gearbox height should I use on a Team Associated RC10 B84/D?
Start with 0 mm, the kit default. It’s the safer baseline if you’re not sure; the setting changes rear differential height. Move to +2 mm for carpet or astroturf. B84/D racers...
What oil setup for Team Associated RC10 B84/D on low-grip indoor clay?
Assuming you mean shock and differential oils, use the B84/D kit values as your baseline, then go lighter in small steps if the car lacks grip. There isn’t a documented B84/D oil...
What ride height should I use on carpet for Team Associated RC10 B84/D?
For the RC10 B84/D, start at 11 mm front and rear on medium-grip carpet. On high-grip carpet, 12 mm front and rear is a good starting point; those are the carpet ride heights used...
