Ask Miles, our Setup AI that’s been trained on the R1B Mark 1.
FMRC BASE
My Base Setup
Training 14.08.2026
Maximus 2026
Test
Stock gearing for the R1WURKS R1B Mark 1, with common pinions and their ratios.
| Pinion | Spur ÷ pinion | FDR |
|---|---|---|
| 18T | 4.33 | 11.27 |
| 19T | 4.11 | 10.67 |
| 20T | 3.90 | 10.14 |
| 21T | 3.71 | 9.66 |
| 22T | 3.55 | 9.22 |
| 23T | 3.39 | 8.82 |
| 24T | 3.25 | 8.45 |
| 25T | 3.12 | 8.11 |
| 26T | 3.00 | 7.80 |
| 27T | 2.89 | 7.51 |
| 28T | 2.79 | 7.24 |
| 29T | 2.69 | 6.99 |
| 30T | 2.60 | 6.76 |
| 31T | 2.52 | 6.54 |
| 32T | 2.44 | 6.34 |
Shaded rows are the pinions most 1/10 2WD buggy setups run on the stock spur.
What pinion should I run?
Tell us your motor and track and get a starting pinion for the R1WURKS R1B Mark 1, with the range racers in the class run.
Get a recommendation →Shop pinion gears at AMain → (opens in new tab)It depends on your motor and the track. In the 1/10 2WD buggy class, racers gear by final drive ratio: 6T and below near 9.40, 7.5–8.5T near 9.22, 17.5T near 6.48. On the R1B Mark 1's stock 78T spur that is about 22T for 6T and below, 22T for 7.5–8.5T, 31T for 17.5T. Tight tracks gear down, open tracks gear up. For a starting pinion matched to your motor, use the So Dialed Pinion Recommender with the R1B Mark 1 selected.
The R1B Mark 1 has an internal ratio of 2.6:1. Final drive ratio = spur ÷ pinion × 2.6. With the stock 78T spur, a 18T pinion gives an FDR of 11.27 and a 32T gives 6.34.
78 teeth. Changing the spur moves every pinion's ratio at once; most racers leave the spur and tune with the pinion.
Kit shock setup. Part numbers link to AMain.
The kit springs are 3.4lb Gray (#920156) front, 1.8lb Green (#920162) rear. Stiffer springs suit high grip and big jumps; softer springs add grip on slick or bumpy tracks.
How do I raise or lower front hub height on an R1WURKS R1B Mark 1?
On the R1WURKS R1B Mark 1, front hub height is adjusted with steering-block shims. The available setup data lists shim options from 0 to 3.5 mm, but it does not specify a reliable...
Nov 11, 2026
Why does my R1B Mark 1 understeer on entry but snap into oversteer with push brake?
First reduce the brake strength in the ESC or radio, then test again. The sudden oversteer under push brake suggests the rear is losing grip when braking; changing the suspension...
Nov 3, 2026
What's the best setup for high-bite carpet on R1WURKS R1B Mark 1?
For a high-bite carpet baseline on the R1WURKS R1B Mark 1, start with Pink-compound tires, a 1.1 mm front anti-roll bar, and a 1.4 mm rear anti-roll bar. These settings come from...
Oct 19, 2026
Free to start · iOS & Android
Your R1WURKS R1B Mark 1 is in the RC Setup App
Save every setup change you make to your R1WURKS R1B Mark 1, get AI tuning answers for that exact car, and log your races — at the track or back in the pits.

