The racer asked
Slow the car down with harder Springs in the Rear ?
Miles, So Dialed's RC setup AI
Stiffer rear springs won't meaningfully slow the car down. They change how the chassis loads and how much grip the rear tires have, not top speed. A stiffer rear spring reduces rear grip and shifts grip to the front, so the car gets looser (more oversteer) in corners. If you want less speed on the straights, change the gearing.
- Drivetrain: Pinion: go down from the kit 24 teeth to lower the final drive ratio. This reduces top speed and runs the motor cooler, but it gives more acceleration.
- Drivetrain: Spur: a bigger spur than the kit 83 teeth has the same effect as a smaller pinion.
Change one at a time. Go down one pinion tooth, make a run, and check motor temperature. If the car is still too fast on the straights, go down another tooth. Changing the gearing also changes how hard the motor works, so keep an eye on heat as you go.
If you tell me your motor (turns or Kv), your track grip, and how long the straights are, I can suggest a pinion and spur that fits.
Follow-up
I want less grip in the rear
Miles
To reduce rear grip, stiffen the rear springs or thicken the rear shock oil. Both shift grip toward the front, so the car gets looser (more oversteer) on entry and mid-corner. Stiffer rear springs also make the rear less willing to hook up on throttle, so watch corner exit.
- Shocks: Rear springs: move one step stiffer than the kit RD2.0 (#YS-RDS). The Yokomo D-170 line runs from Blue (softest) through Black, Pink, Yellow to Green (hardest), and the car's listed rear options include the Prog 1.4x26.5mm (#D-182R) and Prog 1.5x26.5mm (#D-183R). Change one spring at a time and test between steps.
- Shocks: Rear oil weight: the kit is 50 wt. Going to 60 wt or 70 wt reduces rear grip further, and it also slows the rear's weight transfer, so the car will feel calmer and less responsive at the rear.
Start with the spring, since it's the easier change to reverse. If the car is still too loose after one step, move to the oil. Don't change both at once, or you won't know which one did the work. If you tell me your track grip level, I can help you pick how far to go.
Answered by Miles, our RC setup AI. Check anything that affects safety or fitment against your manual.
More RD2.0 questions
Why does my Yokomo RD2.0 spin out and feel like ice vs my other RD2.0?
Spinning out and feeling like ice usually means the rear is losing grip on throttle, and the cause is most likely whatever differs between your two RD2.0s. Since you didn't say...
How do I slow down the chassis on a Yokomo RD2.0?
To calm a quick, snappy RD2.0 and slow how fast it rotates, add rear grip. A car that swings its tail around too quickly is oversteering, and more rear grip makes it more stable....
How much rear toe-in should I run on a Yokomo RD2.0 on low-grip concrete?
Start with about 1.5 degrees of rear toe-in, the value other RD2.0 racers run on low grip concrete tracks. The 1/10 drift class baseline also starts at +1 degree of rear toe, so 1...
What's the stock front alignment on a Yokomo RD2.0?
The RD2.0 kit setup data doesn’t specify a factory front toe angle. Assuming you mean toe, 0° (straight ahead) is the neutral baseline; the listed adjustment range is +3° to −5°.
Why does my Yokomo RD2.0 keep spinning out on P-tile?
If the rear is snapping around on P-tile, first confirm your tires are actually intended for that surface, then make one small increase in rear toe-in. More rear toe-in generally...
