The racer asked
Spins out compared to my other rd2.0 and basically same stuff feels like driving on ice
Miles, So Dialed's RC setup AI
Spinning out and feeling like ice usually means the rear is losing grip on throttle, and the cause is most likely whatever differs between your two RD2.0s. Since you didn't say what changed, I can't tell which one it is yet.
For a rear that breaks loose on throttle, the usual fixes are:
- Rear diff: loosen it. Tightening adds rear stability and loosening removes it, so for oversteer you loosen.
- Rear springs: soften them. A stiffer rear spring takes grip from the rear, so going softer adds it back. The kit rear spring is the RD2.0 (#YS-RDS).
- Rear shock oil: go thinner. Your kit rear oil is 50 wt, and a thicker oil at the rear takes grip away there.
Before changing anything, check the plastic tires for wear, debris, or a dirty track surface. Worn or dusty tires can feel exactly like ice.
What is different between the two cars? Tell me any part you swapped, such as springs, shock oil, diff fluid, tires, or motor and pinion. Also tell me whether the spin happens on throttle exit or while braking or turning in. That will tell me which single change to make first.
Follow-up
Loosen? You said that removes grip. Also how do I do iy
Miles
Loosening the diff doesn't take grip away from the tires. It lets the two rear wheels turn at different speeds more easily, so the rear has less locking force holding it straight. That makes the rear rotate more readily, which is the wrong direction for a rear that is already spinning out. I should have been clearer. Loosening is the right move only if the car is oversteering, so it's worth confirming that's what you're seeing.
I also need to correct my last message. For rear oversteer, the fix is thicker rear shock oil, not thinner. Thicker rear oil reduces rear grip and lets the rear settle, while thinner oil adds rear grip and would make the spin worse.
To loosen the diff on the RD2.0's gear differential:
- Diff adjustment: back off the adjusting nut or screw on the gear diff by a small amount, then test. This is a general method, since the material doesn't give a procedure for this car.
- Diff fluid: a thinner fluid loosens the diff. The kit fluid is 7,500 cst, so step down the list, such as 5,000 cst, to loosen it.
Change only one of these, then run a few laps. If the car starts to feel vague, or the rear wheels spin on corner exit, you have gone too far, so go back toward the kit setting. If it still spins out after that, the next change is the rear shock oil, moving thicker.
Follow-up
What screw on the diff
Miles
I can't confirm a screw on the RD2.0's gear diff, so I shouldn't have described one. Changing the diff fluid is the adjustment I can confirm for this car, so use that instead:
- Differential fluid: step down from the kit 7,500 cst to a thinner option such as 5,000 cst. Thinner fluid loosens the diff.
I also need to correct my last message. For rear oversteer, the setup chart calls for thinner rear shock oil, not thicker. My earlier statement that thinner oil makes the spin worse was wrong. Thinner rear oil lets the rear tires keep more grip, which is what you need when the rear is breaking loose.
Your rear options, one at a time:
- Rear diff fluid: go thinner, from 7,500 cst to 5,000 cst.
- Rear shock oil: go thinner than the kit 50 wt.
- Rear springs: go softer than the kit RD2.0 (#YS-RDS).
Start with the diff fluid, since it is the lowest-cost change. Run a few laps before changing anything else. If the car feels vague or the rear spins on corner exit, you have gone too far, so go back toward the kit setting.
Answered by Miles, our RC setup AI. Check anything that affects safety or fitment against your manual.
More RD2.0 questions
Will harder rear springs slow down my Yokomo RD2.0?
Stiffer rear springs won't meaningfully slow the car down. They change how the chassis loads and how much grip the rear tires have, not top speed. A stiffer rear spring reduces...
How do I slow down the chassis on a Yokomo RD2.0?
To calm a quick, snappy RD2.0 and slow how fast it rotates, add rear grip. A car that swings its tail around too quickly is oversteering, and more rear grip makes it more stable....
How much rear toe-in should I run on a Yokomo RD2.0 on low-grip concrete?
Start with about 1.5 degrees of rear toe-in, the value other RD2.0 racers run on low grip concrete tracks. The 1/10 drift class baseline also starts at +1 degree of rear toe, so 1...
What's the stock front alignment on a Yokomo RD2.0?
The RD2.0 kit setup data doesn’t specify a factory front toe angle. Assuming you mean toe, 0° (straight ahead) is the neutral baseline; the listed adjustment range is +3° to −5°.
Why does my Yokomo RD2.0 keep spinning out on P-tile?
If the rear is snapping around on P-tile, first confirm your tires are actually intended for that surface, then make one small increase in rear toe-in. More rear toe-in generally...
