The racer asked
Which tires for a freezing cold track
Miles, So Dialed's RC setup AI
For a freezing-cold track, start with a soft or super-soft compound. Cold tires need a softer compound to conform to the surface and generate grip; the right tread still depends on whether the track is clay, dirt, carpet, or turf.
- On clay, use slicks or ghost slicks if the surface is smooth and clean. On dirt, choose the tread for the surface: pins for loose dirt, and bar-style tread for a clean, grooved surface.
- Compound labels vary by brand. For example, Captic lists Super Soft for 0–12°C, while Pro-Line lists M4 and S4 for below 70°F.
Avoid choosing solely by the air temperature: track surface and grip matter too. What is the surface, and is it dusty, damp, or clean and grooved?
Follow-up
Clay and dusty
Miles
On cold, dusty clay, use a soft or super-soft compound and a tread that can bite through the dust. I’d start with a dense-pin or connected-square-pin tire, rather than a slick; slicks work better once the clay is clean and tacky. Dense pins are recommended for hard surfaces with a loose, dusty layer, and softer tires suit dusty, low-grip conditions.
For example, Pro-Line’s Electron 2.0 is listed for dusty hard-pack conditions; choose its softer option if available for your tire position.
If the dust gets swept off and the clay starts to grip, try a clay slick or ghost slick instead. Watch tire wear with the soft compound, especially if the surface is abrasive.
Follow-up
Does it make a difference glue has been placed on the freezing cold clay
Miles
Yes. If you mean traction compound applied to the track, it can make treated sections gripier, but on freezing-cold, dusty clay the effect may be weak or uneven. The dust can sit on top of the treated surface, and cold conditions can slow how well the compound works.
I’d still start with a soft-compound tire suited to dusty clay, but avoid going straight to the most aggressive pin if the track has sticky patches. If the car suddenly grips hard, starts traction-rolling, or feels inconsistent from corner to corner, try a less aggressive tread or a firmer compound. If the glue is only on certain areas, expect the handling to change as you cross them.
Is the compound spread across the whole track, or just on patches?
Follow-up
The whole track
Miles
If traction compound is spread over the whole track, grip should be more consistent around the lap, but it doesn’t automatically make dusty clay a slick-tire surface. Dust on top can still reduce the tire’s bite.
For your cold, dusty clay, I’d still start with a soft compound and a treaded tire. If the treated surface is swept clean and feels tacky, then try a clay slick; slicks are suited to high-grip clay with little dust.
Watch for the car gaining grip as the track gets driven in. If it starts traction-rolling, try a firmer compound; if it still slides on the dusty layer, stay with the treaded tire.
Follow-up
Which tire brand, tread and compound do you recommend for the front and rear tires
Miles
For your B7.1 on freezing, dusty clay treated across the whole track, I’d start with Pro-Line Hole Shot 3.0 M4 tires front and rear: the 2WD front and rear versions. Their mini-pin tread is suited to dusty hard pack, and M4 is the cooler-condition option listed for the 2WD front.
- Front: Hole Shot 3.0 2WD front, M4 compound. Its angled outer pins help maintain steering bite.
- Rear: Hole Shot 3.0 rear, M4 compound. The square mini-pins help the rear find grip through the dusty layer.
Since the whole track is treated, see how much grip builds as it gets run in. If the dust clears and the surface becomes clean and tacky, try a slick or lower-profile clay tire; slicks are better suited to tacky or dust-free clay.
Answered by Miles, our RC setup AI. Check anything that affects safety or fitment against your manual.
More RC10 B7.1/B7.1D questions
What setup changes for a Team Associated RC10 B7.1 on low-grip astroturf?
There isn't a public low-grip astroturf setup to copy. The only astroturf setup is medium grip, so I'd start from it and make a few changes toward more traction. Those changes are...
How can I get more low-speed steering on a Team Associated RC10 B7.1/B7.1D?
For a sharper steering response at low speed, try KPI 3 if you’re currently at KPI 0. The B7 setup tips describe KPI 3 as the most direct steering feel, while KPI 0 is less...
What pill setting for wide C and D blocks on RC10 B7.1/B7.1D?
For a wide rear pivot on the B7.1/B7.1D, set the C- and D-block inserts to the positions that give the widest hinge-pin spacing, and mirror the left and right sides. There isn’t...
RC10 B7.1: 69T vs 72T spur with 17.5T motor — which is better?
A 69T spur gives taller gearing than a 72T spur with the same pinion: about 4.2% more rollout, so it can gain speed on a long straight. It also gives up some wheel torque, which...
Gearing for RC10 B7.1 with Hobbywing V10 G5 17.5T?
For the RC10 B7.1 with the Hobbywing V10 G5 17.5T Torque, start with a 31T pinion and the stock 78T spur. That gives a 6.54:1 final drive ratio; confidence is high for this...
How do I set up a Team Associated RC10 B7.1/B7.1D for a Nor‑Cal track?
Nor-Cal’s name alone doesn’t tell me the surface or grip, so there isn’t one reliable track-specific setup. If you mean a low-grip clay layout, use these B7.1D settings as a...
