Ask Miles, our Setup AI that’s been trained on the RC10 B6.3.
Finish line Turf masters race 3/12/22
MB Models - glued down staggers
Robin hood raceway dry
Spring Fling Rd 1
My Base Setup 21.5
PP_SilverstoneTuesClub_21/11/23
MB Models
My Base Setup
AE B6.3 BMR Nationals 2022
MB Raceway
Trains & Lanes
My Setup Cactus
Grass Mid East regional WBMCC
My Base Setup
Matty Gs Nats setup
TRAC Setup 16/01/2022
My Base Setup
My Base Setup
Stock gearing for the Team Associated RC10 B6.3, with common pinions and their ratios.
| Pinion | Spur ÷ pinion | FDR |
|---|---|---|
| 18T | 4.33 | 11.27 |
| 19T | 4.11 | 10.67 |
| 20T | 3.90 | 10.14 |
| 21T | 3.71 | 9.66 |
| 22T | 3.55 | 9.22 |
| 23T | 3.39 | 8.82 |
| 24T | 3.25 | 8.45 |
| 25T | 3.12 | 8.11 |
| 26T | 3.00 | 7.80 |
| 27T | 2.89 | 7.51 |
| 28T | 2.79 | 7.24 |
| 29T | 2.69 | 6.99 |
| 30T | 2.60 | 6.76 |
| 31T | 2.52 | 6.54 |
| 32T | 2.44 | 6.34 |
Shaded rows are the pinions most 1/10 2WD buggy setups run on the stock spur.
What pinion should I run?
Tell us your motor and track and get a starting pinion for the Team Associated RC10 B6.3, with the range racers in the class run.
Get a recommendation →Shop pinion gears at AMain → (opens in new tab)It depends on your motor and the track. In the 1/10 2WD buggy class, racers gear by final drive ratio: 6T and below near 9.40, 7.5–8.5T near 9.22, 17.5T near 6.48. On the RC10 B6.3's stock 78T spur that is about 22T for 6T and below, 22T for 7.5–8.5T, 31T for 17.5T. Tight tracks gear down, open tracks gear up. For a starting pinion matched to your motor, use the So Dialed Pinion Recommender with the RC10 B6.3 selected.
The RC10 B6.3 has an internal ratio of 2.6:1. Final drive ratio = spur ÷ pinion × 2.6. With the stock 78T spur, a 18T pinion gives an FDR of 11.27 and a 32T gives 6.34.
78 teeth. Changing the spur moves every pinion's ratio at once; most racers leave the spur and tune with the pinion.
Kit shock setup. Part numbers link to AMain.
Out of the box the RC10 B6.3 runs 45 wt front, 35 wt rear, on 2mm 2x1.5mm FT v2 (#91895) front, 2mm 2x1.6mm FT v2 (#91896) rear pistons. That is the kit setup; you will need to adjust it for your track conditions. The RC Setup App can help dial it in.
The kit springs are 4.60lb Red (#91835) front, 2.20lb Blue (#91840) rear. Stiffer springs suit high grip and big jumps; softer springs add grip on slick or bumpy tracks.
What shock oil should I run on a Team Associated RC10 B6.3 for high-grip carpet?
For the RC10 B6.3, a common high-grip carpet starting point is 45 wt front and 35 wt rear. Other high-grip carpet setups also use 35–40 wt front and 30–32.5 wt rear, so treat...
Oct 28, 2026
What shock oils for Team Associated RC10 B6.3?
For the RC10 B6.3 kit setup, start with 45 wt front and 35 wt rear shock oil, using Team Associated oil as the reference. Those are the model’s default oil weights. Thicker oil...
Oct 28, 2026
Team Associated RC10 B6.3 starter setup for racing at MB Models?
I can give you a B6.3 starter sheet, but I can’t confirm MB Models’ current surface or grip. This baseline assumes medium-grip, hard-packed dirt; if you’re racing carpet or...
Oct 26, 2026
What pinion gear for RC10 B6.3 with a 17.5T motor?
For your Team Associated RC10 B6.3 with a 17.5T motor, start with a 31T pinion and the stock 78T spur. That gives a 6.54:1 final drive ratio; confidence is high. After a short...
Oct 24, 2026
Free to start · iOS & Android
Your Team Associated RC10 B6.3 is in the RC Setup App
Save every setup change you make to your Team Associated RC10 B6.3, get AI tuning answers for that exact car, and log your races — at the track or back in the pits.

